Who might need mesh Wi-Fi across multiple floors?

Viewers with a Wi-Fi dead spot on another floor

If ceilings or a distant router are affecting reception at your TV, choosing the right locations for your mesh nodes is key. The F.A.Z. Kaufkompass highlights the importance of the connection between nodes when positioning them.

Households with Ethernet between floors

If you can connect the nodes via Ethernet, you can avoid a wireless connection between them. The F.A.Z. Kaufkompass describes wired Ethernet as a less interference-prone backhaul; TP-Link explains how to set up Ethernet backhaul for Deco systems.

Households with an existing router and a limited budget

If you only need to cover a distant floor, it may be worth looking at an extender before replacing your whole system. FRITZ! also describes its Mesh Set 2700 as suitable for connecting to another router; the right way to integrate it depends on the system. Deloitte Deutschland points out that the best solution can vary depending on reception and the building.

What should you look for when buying?

First, check reception where you’ll watch the recording and at potential node locations, then look at the connection between floors. Next, work out whether you want to integrate your existing router and whether the bottleneck is actually in your home network.

What matters What to check before buying Who should pay particular attention?
Coverage across floors Reception at the TV and planned node locations; how many units you need. If I want to watch a recording in a room with poor reception, I need suitable node locations rather than a device that’s itself stuck in a dead spot. Around 33% of consumers say coverage on distant floors is their top concern.
Connection between floors Existing Ethernet, the system’s backhaul support and operating mode; check which connection is actually being used after setup. If there’s an Ethernet cable between floors, I want to be able to use it to connect the nodes. Around 25% of consumers prioritise a stable backhaul.
Router and total cost Compatibility and operating mode, the number of units you need, and any costs for additional features. If my router still works, I want to check whether I can keep using it rather than replacing the whole network unnecessarily. Around 25% of consumers prioritise integrating existing devices and keeping overall costs manageable.
Multiple people using the network Online or local playback, the connection on the playback device and the requirements of the streaming service. If other people are using the network while I watch the recording, I want to know whether the bottleneck is the Wi-Fi or the internet connection. Around 17% of consumers focus on playback while other devices are in use.

What mistakes should you avoid?

  • Placing an extra node in the dead spot

    A node needs a decent connection to the rest of the network itself. Reception at the node alone doesn’t tell you whether its backhaul connection is stable enough.

    Choose an intermediate location with a good connection, or use existing Ethernet. After setup, check which connection the node is actually using.

    Adding another node or installing cables later could mean extra setup work.

  • Assuming every device labelled ‘mesh’ is compatible

    Mesh systems from different product families aren’t automatically compatible. TP-Link explicitly distinguishes between Deco Mesh and OneMesh.

    Before combining devices, check the documented support for your router and the operating mode you plan to use.

    If the devices can’t be integrated properly, you may need to run a separate system or replace your existing equipment.

  • Assuming Wi-Fi 7 automatically includes a 6 GHz band

    The German TP-Link Deco BE25 datasheet lists Wi-Fi 7, but only the 2.4 and 5 GHz bands. The Wi-Fi generation alone doesn’t tell you which bands a particular model uses.

    Check the listed Wi-Fi bands for the exact model and version.

  • Blaming every pause in an internet stream on Wi-Fi

    A mesh system distributes the connection around your home, but it can’t replace a good internet connection. For a locally stored recording, the source and your home network are what matter.

    Compare playback near the router with playback at the viewing location, and check whether the recording is available online or locally.

    If the bottleneck is your internet connection, buying an extra mesh node may not solve the problem.

Which mesh Wi-Fi brands are worth considering?

TP-Link

The Deco range includes standalone mesh systems. The German Deco BE25 datasheet lists dual-band Wi-Fi 7 and two 2.5 Gbit/s ports per unit.

  • TP-Link lists wired and wireless backhaul for the BE25.
  • According to the specifications, the BE25 uses the 2.4 and 5 GHz bands; Deco Mesh and TP-Link OneMesh aren’t compatible with each other.

FRITZ!

FRITZ! describes the Mesh Set 2700 as a two- or three-unit set for extending a FRITZ!Box network or connecting to another router.

  • According to FRITZ!, each repeater supports Wi-Fi and LAN connections and has a 2.5 Gigabit LAN port.
  • The right set size depends on the layout of your home; a general range figure can’t replace checking the conditions on site.

ASUS

ASUS describes the ZenWiFi XT9 as a tri-band Wi-Fi 6 mesh pair that can use either wireless or wired backhaul.

  • ASUS documents Ethernet backhaul and additional options for wireless backhaul.
  • ASUS notes that certain 160 MHz and UNII-4 features may be restricted in some regions. Check the details for the specific version you’re considering.

eero

The German eero documentation describes the eero 6+ as a dual-band Wi-Fi 6 system with two 1 GbE ports per device.

  • These ports may be useful when planning which devices to connect by Ethernet.
  • Before buying, check that setting up and managing the system through the app is right for your household.

Mesh Wi-Fi products at Joybuy

This selection includes two- and three-node mesh sets for covering multiple areas and potentially integrating an existing router. Before buying, check that the connections, operating mode and documentation for the exact version on offer are suitable for your network.

TP-Link Deco BE22, two-unit set, Wi-Fi 7, dual-band

TP-Link Deco BE22, 2-pack, Wi-Fi 7

The two Deco units are worth considering if you want to position mesh nodes in different areas of your home.

Dual-band Wi-Fi 7; two Gigabit WAN/LAN ports per unit.

View at Joybuy
TP-Link Deco M4, three-unit set, AC1200, dual-band

TP-Link Deco M4, 3-pack, AC1200

This three-unit set may suit households looking to cover several areas and integrate an existing router in Access Point mode.

Wi-Fi 5, dual-band and two Gigabit LAN/WAN ports per unit. According to the description, setup is via the Deco app and requires an account.

View at Joybuy
TP-Link Deco S4, three-unit set, AC1200

TP-Link Deco S4, 3-pack, AC1200

This three-unit set may suit you if you want to cover several areas with mesh nodes and keep using an existing modem or router.

Dual-band and Gigabit Ethernet ports per unit. According to the description, setup and network management are handled through the Deco app.

View at Joybuy
MERCUSYS Halo H3000X, two-unit set, Wi-Fi 6 AX3000

MERCUSYS Halo H3000X, 2-pack, Wi-Fi 6 AX3000

The two Halo units are worth considering if you want to position mesh nodes in different areas of your home.

Dual-band Wi-Fi 6 and three Gigabit ports per unit. According to the description, setup and management are handled through the MERCUSYS app.

View at Joybuy
MERCUSYS Halo H25BE, two-unit set, Wi-Fi 7 BE3600

MERCUSYS Halo H25BE, 2-pack, Wi-Fi 7 BE3600

This two-unit set may suit you if you want to position mesh nodes around your home and set one unit up as the main router.

Dual-band Wi-Fi 7 and three Gigabit ports per unit. According to the description, the main unit is set up through the MERCUSYS app.

View at Joybuy

Frequently asked questions

Are the Wi-Fi speeds shown on the box fast enough for a theatre recording?

The Wi-Fi speeds shown on the box don’t guarantee the speed you’ll get at your TV. Check whether the recording is available online or locally, and test the connection where you’ll watch it. Netflix recommends at least 5 Mbit/s for Full HD and 15 Mbit/s for 4K; these aren’t general requirements for every theatre recording.

How do I set up a wired backhaul?

For a Deco system, TP-Link recommends setting up the units in the app first, then connecting them by cable in a way that suits your router or Access Point mode. Afterwards, check the network view to confirm that the satellite is actually using Ethernet backhaul; setup may differ on other systems.

Are there any extra costs beyond buying the device?

Extra costs could include additional nodes, cabling or optional add-on services. If a feature is offered separately, check the relevant terms and conditions before buying.

What should I do regularly after setup?

The German Federal Office for Information Security recommends changing default passwords and keeping your router’s firmware up to date. Also check the connection where you’ll actually watch the recording.

What legal requirements apply to a Wi-Fi device sold in Germany?

The German Federal Network Agency describes CE marking and the necessary conformity documentation as requirements for relevant products. Retailers must also check that the required accompanying documentation, such as user manuals and safety information in German, is provided. You can’t tell whether a specific version meets these requirements from the brand name alone.