Who is mesh Wi-Fi across multiple floors for?

People presenting across multiple floors

You need Wi-Fi both where you’re giving a presentation or holding a meeting and at the nodes that pass the signal on. The F.A.Z. Kaufkompass and FRITZ! both highlight node placement and the connection between nodes as important factors to consider when planning your setup.

Teams sharing screens wirelessly

You want to connect a screen receiver to your presentation device. For Google Cast, Google’s Help Centre lists a shared Wi-Fi network and disabled AP isolation as requirements.

People using an existing router

You want to extend your coverage without replacing your internet router unnecessarily. FRITZ! and TP-Link describe different operating modes and compatibility requirements, so check what applies to your specific devices.

What should you look for when choosing?

First, check how you’ll share your screen and what the connection is like in the planned locations. This will help you work out whether LAN, Wi-Fi or Powerline is the best option for connecting the nodes.

What you need What to check before buying Who will find this particularly important?
Coverage where you’re presenting Check reception in the rooms concerned and consider possible locations for the nodes. If I need to present on several floors, Wi-Fi at the actual presentation location matters. Around 36% of consumers give top priority to coverage where they present.
Connection between the nodes Check for existing LAN cabling, available ports and the backhaul mode; if needed, test Powerline using the sockets you plan to use. If the Wi-Fi signal may struggle to pass through floors, I want to know whether there’s LAN cabling or whether the nodes will connect via Wi-Fi or the electrical wiring. Around 29% of consumers focus above all on a stable backhaul connection between floors.
Connecting to the screen Check the screen-sharing method and network access for the devices involved; with Google Cast, also check AP isolation. If my presentation device needs to find the screen receiver, communication on the specific network is crucial. Around 21% of consumers prioritise being able to connect to the presentation screen.
Connecting to your existing network Check the operating mode, router compatibility and any app or management settings required. If I want to keep using my existing router, the additional system needs to be compatible with its operating mode and the way I want to manage my network. Around 14% of consumers focus on integrating the system with their existing network and the settings involved.

What mistakes should you avoid?

  • Assuming mesh coverage means screen sharing will work

    With Google Cast, AP isolation can prevent devices from communicating even when both are connected to Wi-Fi. A guest network may also restrict access between devices.

    Test your chosen screen-sharing method with the devices and networks you plan to use before buying more nodes because a screen can’t be found.

  • Putting a mesh node in a dead zone

    The node itself needs a reliable connection to the rest of your network. Ethernet backhaul requires suitable cabling and ports.

    Check the connection between the nodes at the planned location, and compare the existing LAN connection with the Wi-Fi signal available there.

  • Assuming Powerline is an interference-free alternative to cabling

    Devolo notes that data rates can be low at some sockets and may be affected by electrical devices. According to the manufacturer, certain VDSL profiles can also experience interference.

    Test the wall sockets you actually intend to use. If you have a VDSL connection, also take into account the possible interaction described by the manufacturer.

  • Assuming Wi-Fi 7 automatically means 6 GHz or good performance across floors

    The German Deco BE25 is described as a dual-band model for 2.4 and 5 GHz. Its combined theoretical data rate is not a measurement of performance in a particular building.

    Check the frequency bands, ports and backhaul options listed for the specific model, rather than assuming the Wi-Fi generation tells you how well it will perform where you’re presenting.

Key brands at a glance

TP-Link

Deco systems are designed as standalone mesh systems. In Germany, the Deco BE25 is described as a dual-band Wi-Fi 7 model with two 2.5 Gbit/s ports per unit.

  • TP-Link lists wired and wireless backhaul for the BE25.
  • The stated combined Wi-Fi data rate of up to 3.6 Gbit/s is not a guaranteed speed across multiple floors. According to TP-Link, you need a mobile app and a TP-Link ID to set up and manage the Deco system.

FRITZ!

According to FRITZ!, the FRITZ!Mesh Set 4200, with two or three FRITZ!Repeaters 3000 AX, can be used as a standalone set with a suitable router or fibre-optic modem, or to extend an existing FRITZ! Mesh network.

  • FRITZ! lists three radio bands across 2.4 and 5 GHz, plus two Gigabit LAN ports per repeater.
  • Using the set on its own and integrating it into an existing FRITZ! Mesh network are different installation options. The theoretical data rate of up to 4,200 Mbit/s doesn’t show what speed you’ll get at your presentation location.

devolo

Magic 2 WiFi 6 next combines Wi-Fi with data transmission over existing electrical wiring. It could be an option if you don’t have LAN cabling or a suitable Wi-Fi connection between floors.

  • devolo offers Starter and Multiroom kits.
  • According to devolo, sockets and electrical devices can affect Powerline data rates. Certain VDSL connections may also experience interference; advertised peak Wi-Fi speeds don’t measure the connection over your electrical wiring.

eero

eero 6+ is a dual-band Wi-Fi 6 system with app-guided setup, for people who prefer a standalone mesh network.

  • eero’s German product listing shows several pack sizes.
  • Additional security and management features are listed there as available by separate subscription. The manufacturer’s claims about video calls aren’t independent measurements for a particular building.

Joybuy products for mesh Wi-Fi and network expansion

This selection includes mesh kits for multiple rooms, as well as an access point for extending an existing network.

TP-Link Deco BE22 Wi-Fi 7 mesh system, 2-pack, white

TP-Link Deco BE22 Wi-Fi 7 Mesh System (2-pack), white

This 2-pack is designed to create a mesh network with two nodes.

Dual-band Wi-Fi 7; Gigabit Ethernet.

View at Joybuy
Ubiquiti U7 Mesh Wi-Fi access point with Power over Ethernet

Ubiquiti U7 Mesh

This access point may suit you if you want to extend an existing network and can provide a suitable network connection and PoE power.

Installation includes configuration through UniFi Network.

View at Joybuy
TP-Link Deco M4 dual-band mesh system, AC1200, 3-pack

TP-Link Deco M4 Dual-Band Mesh System AC1200 (3-pack)

This three-unit kit is designed to spread a mesh network across multiple rooms.

Dual-band; Gigabit ports.

View at Joybuy
MERCUSYS Halo H3000X Wi-Fi 6 mesh system, AX3000, 2-pack

MERCUSYS Halo H3000X Wi-Fi 6 Mesh System AX3000 (2-pack)

This 2-pack is designed to create a shared mesh network across multiple rooms.

Dual-band Wi-Fi 6; three Gigabit ports per unit; WPA3.

View at Joybuy
MERCUSYS Halo H25BE Wi-Fi 7 mesh kit, BE3600, 2-pack

MERCUSYS Halo H25BE Wi-Fi 7 Mesh Kit BE3600 (2-pack)

This two-unit kit is designed to create a mesh network with a main unit and an additional node.

Dual-band Wi-Fi 7; three Gigabit ports per unit; WPA3.

View at Joybuy

Frequently asked questions

Is a high advertised Wi-Fi data rate enough for a presentation on another floor?

No. What matters is the connection where you’re presenting and the backhaul between the nodes. The F.A.Z. Kaufkompass describes wired backhaul as generally less susceptible to interference and capable of higher data rates; this isn’t a guarantee of performance in a particular building.

Why can’t I see a Google Cast screen even though I have mesh Wi-Fi?

According to Google’s Help Centre, for the Android screen-casting method described, the Android device and Cast receiver must be connected to the same Wi-Fi network, and AP isolation must be disabled. Check that these requirements are met for your specific screen-sharing method; they don’t automatically apply to every presentation protocol.

How do I set up a LAN connection between Deco nodes?

First, set up the nodes using the Deco app, then connect them by cable in a way that suits your router or access point mode. TP-Link notes that an older general guide to Ethernet backhaul shouldn’t automatically be applied to the BE25. Check the connection shown in the app and follow the guidance for your specific model.

Do I need 6 GHz Wi-Fi for a presentation across multiple floors?

No, 6 GHz isn’t a general requirement for this scenario. If you choose a device with 6 GHz capability, the applicable German frequency allocation rules and the specific device version will determine how it can be used. The Bundesnetzagentur lists Verfügung 76/2025 for this and has revoked the earlier Verfügung 12/2025.