Who can benefit from mesh Wi-Fi across multiple floors?

Households with Wi-Fi dead spots on other floors

If your TV gets a weak Wi-Fi signal on another floor, you’ll need to find suitable locations for the mesh nodes and make sure they can connect reliably to one another. The F.A.Z. Kaufkompass and TP-Link both identify these as important factors for Wi-Fi coverage across multiple floors.

Households streaming on several devices at once

If you stream on several devices, consider the connection at each playback device and the demands on your network, rather than comparing advertised maximum Wi-Fi speeds alone. Netflix has its own recommendations for streaming quality, while the F.A.Z. Kaufkompass also looks at the connection between mesh nodes.

Households with an existing mesh router

If you want to extend an existing FRITZ! or Speedport network, check that your specific router and range extender are compatible. FRITZ! and Telekom each outline the requirements for their mesh solutions.

What matters when streaming across multiple floors?

Start by measuring the connection at your TV. Then check whether you have cables between floors and which router or mesh components you already use at home.

What you need What to check before buying Who is this most relevant to?
Coverage on the floor where you watch films Check the floors involved, available sockets and connection quality between the nodes. If my TV is on another floor, I need a signal there and suitable locations for any intermediate nodes. Around 36% of consumers prioritise coverage on the floor where they watch films.
Reliable streaming with minimal interruptions Measure the speed at your playback device and weigh up wired or wireless backhaul. If I want to watch a film without buffering, both the connection at the TV and the route it takes to get there matter. Around 29% of consumers make reliable streaming their top priority.
Compatibility with your router and internet connection Check your router model, firmware, operating mode and the connection used by the main node. If I want to keep using my existing router, the specific combination needs to work with my network. Around 21% of consumers take their existing equipment into account first.
Set-up and extra features Compare the number of units in the pack, the set-up process and any extra features you need. If I need a suitable number of nodes and a set-up process that works for me, I want to know what’s involved in advance. Around 14% of consumers prioritise ease of use and extra features.

Common mistakes when choosing a mesh system

  • Assuming the advertised maximum Wi-Fi speed is the same as the speed at your TV

    A manufacturer’s Wi-Fi speed rating doesn’t tell you what speed will reach your playback device through ceilings and walls. Your internet connection may also be a limiting factor.

    Start by measuring the speed at your TV or streaming device. Then compare the backhaul and Wi-Fi class.

  • Putting the mesh node right in the existing Wi-Fi dead spot

    Each node needs a decent connection to the rest of the mesh. Adding another node won’t help much if its own backhaul connection is weak.

    Check possible intermediate locations and the connection indicator. If you have Ethernet between floors, consider using wired backhaul.

  • Assuming mesh compatibility from the brand name alone

    Not every router from a particular brand can act as a mesh base station. A standalone mesh system also needs a suitable internet connection.

    Before buying, check the router model, firmware and intended operating mode against the range extender.

  • Thinking you need a 6 GHz band to stream a film

    TP-Link describes the Deco XE75 as a tri-band system with a 6 GHz band, and the Deco BE25 as a dual-band system. Even so, the connection you get at home depends on the actual locations of the nodes and local Wi-Fi conditions.

    Compare extra bands with your specific needs rather than treating them as a substitute for checking node locations.

Key mesh Wi-Fi brands at a glance

TP-Link

The Deco range includes mesh systems with different Wi-Fi standards and pack sizes.

  • TP-Link lists two 2.5 Gbit/s ports per unit on the BE25, along with wired and wireless backhaul. The XE75 also has a 6 GHz band.
  • TP-Link requires a TP-Link ID and its mobile app to configure a Deco system. Band and port specifications don’t guarantee a connection through any particular floor.

FRITZ!

The FRITZ!Mesh Set 4200 is available with two or three FRITZ!Repeater 3000 AX units.

  • FRITZ! says it can be connected to a router or fibre-optic modem. For the three-unit set, the manufacturer lists three tri-band repeaters and automatic updates.
  • The right set size depends on your floor plan and the locations available. A stated Wi-Fi performance figure doesn’t measure streaming speed at your TV.

Telekom

Speed Home WLAN is a mesh extender for compatible Speedport set-ups.

  • Telekom lists Wi-Fi and Ethernet connections, as well as mesh support with compatible Speedport routers.
  • According to Telekom, the Speedport Smart and Smart 2 can’t act as mesh base stations themselves. The specific router model is what matters.

eero

eero 6+ is an app-based Wi-Fi 6 mesh option available in different pack sizes.

  • eero describes app-based set-up and the option to extend the network with additional eero devices.
  • The advertised coverage isn’t a measurement for a specific home. Check that the planned locations work with your own floor plan.

Joybuy products for mesh Wi-Fi across multiple floors

The selection includes multi-node wireless mesh systems and a single Deco extender for an existing Deco network. None of the sets guarantees a signal through any particular floor.

TP-Link Deco M4 AC1200 mesh Wi-Fi system, 3-pack

TP-Link Deco M4 AC1200 mesh Wi-Fi system, 3-pack

This three-unit set may suit households planning to use several nodes and possibly keep an existing router. If so, check the intended operating mode.

Dual-band AC1200; Gigabit ports.

View at Joybuy
TP-Link Deco S4 AC1200 mesh Wi-Fi system, 3-pack

TP-Link Deco S4 AC1200 mesh Wi-Fi system, 3-pack

This three-unit set is an option for households considering several mesh locations and looking to connect wired devices to a node.

Dual-band AC1200; two Gigabit ports per unit.

View at Joybuy
MERCUSYS Halo H3000X Wi-Fi 6 AX3000 mesh system, 2-pack

MERCUSYS Halo H3000X Wi-Fi 6 AX3000 mesh system, 2-pack

This two-unit set is an option if you’re planning to use two mesh locations. Check that both nodes will have a suitable connection where you intend to place them.

Dual-band; three Gigabit ports per unit.

View at Joybuy
MERCUSYS Halo H25BE Wi-Fi 7 BE3600 mesh set, 2-pack

MERCUSYS Halo H25BE Wi-Fi 7 BE3600 mesh set, 2-pack

This two-unit set may suit a floor plan that works with two nodes. Position the second node so it can get a suitable connection to the first.

Dual-band; three Gigabit ports per unit.

View at Joybuy
TP-Link Deco X10 Wi-Fi 6 AX1500, single extender unit

TP-Link Deco X10 Wi-Fi 6 AX1500, single extender unit

According to the product description, this single unit is designed to extend an existing Deco mesh, rather than work as a standalone multi-node set.

Dual-band; two Gigabit ports.

View at Joybuy

Frequently asked questions about mesh Wi-Fi and streaming

How many mesh nodes do I need for multiple floors?

Don’t base the number on floor area alone. Check where your TV is, where you could place intermediate nodes and, with wireless mesh, the connection between each node. For example, FRITZ! offers the Mesh Set 4200 with two or three repeaters; that doesn’t guarantee coverage in any particular home.

Where should I check whether my connection is fast enough for a film?

Measure the connection as close as possible to your TV or streaming device. For its own streaming service, Netflix recommends at least 3 Mbit/s for HD, 5 Mbit/s for Full HD and 15 Mbit/s for 4K. These guidelines don’t replace checking Wi-Fi stability or taking other simultaneous use into account.

Do I have to replace my internet router to get a new mesh system?

Not necessarily. TP-Link describes Deco as a system that needs an external internet source, while FRITZ! says the Mesh Set 4200 connects to a router or fibre-optic modem. Check the intended operating mode for the specific device you’re connecting it to.

What does CE marking mean on a mesh Wi-Fi device?

Where a mesh Wi-Fi radio device is subject to the relevant EU harmonisation requirements, it must carry the required CE marking. The Bundesnetzagentur explains that the manufacturer uses it to declare conformity under its own responsibility; it isn’t an independent performance test.

What should I check after installation?

Check the connection at each node’s final location and keep the firmware up to date. Telekom points out that missing firmware updates can lead to malfunctions and security vulnerabilities.