Who could benefit from an audio interface?

Archiving stereo cassette tapes

If you want to record and monitor both channels from your cassette deck separately, two suitable line inputs and a stereo monitoring function are important. The Audacity Manual recommends using a stereo setting when recording cassettes.

Monitoring the transfer as it happens

If you want to check the signal and levels through headphones while recording, look for direct monitoring and a level meter. Focusrite and MOTU document these features for their respective models.

Working at a small desk

If space is tight for your cassette deck, interface and headphones, check the connection positions and allow room for plugged-in cables as well as looking at the unit’s dimensions. MOTU lists the M2 as measuring 19,05 × 10,8 × 4,5 cm.

What should you look for when buying?

For stereo cassettes, start with two suitable line inputs and genuine stereo monitoring. Then consider level control and how much space the interface needs.

What matters What to check before buying Who is it important to?
Stereo signal path Two line inputs that can be used at the same time; make sure the recording software treats the left and right channels separately as stereo. If I want to preserve a cassette in full stereo, the left and right channels need to be recorded separately. Around 33% of consumers put preserving the stereo signal first.
Monitoring while recording Check for a headphone output and a documented stereo direct monitoring function on the specific model; if you hear an echo, check software monitoring too. If I want to monitor the transfer through headphones, I need direct monitoring that keeps the channels separate. Around 27% of consumers prioritise headphone monitoring while recording.
Checking levels Check for a line mode and an input or clip indicator. The Audacity Manual gives peaks around −6 dB as a recording guideline, not a device specification. I want to check the loudest part before recording, so the transfer doesn’t clip. Around 20% of consumers put level control first.
Space for the unit and cables Allow for the unit’s dimensions and room for plugs and cables; make sure the controls and indicators are accessible in your setup. At a small desk, I want to fit my cassette deck, interface and connected cables without covering the controls. Around 20% of consumers prioritise a compact footprint.

Common buying and connection mistakes

  • Assuming two inputs guarantee reliable stereo monitoring

    A Direct Mono mode can combine both input signals in the monitor output. This means you won’t hear the cassette’s left and right channels separately.

    Check the specific model’s manual for its mono/stereo mode, then test the setting with a short stereo recording.

  • Connecting the cassette deck to a microphone input

    The Audacity Manual notes that a microphone input can amplify a playback device’s stronger line-level signal too much. If the recording clips, you may need to transfer the tape again.

    Connect the deck’s line output to suitable line inputs, keeping the left and right channels separate. Check the levels before recording the whole tape.

    A faulty recording means spending extra time on the transfer.

  • Comparing only the size of the unit

    The connection layout and plugged-in cables need space too. On a small desk, cables or hard-to-reach controls can make the setup impractical.

    Measure the space you have, including plugs and cable runs, and check that the inputs, headphone socket and controls will remain accessible.

    Depending on the connections you already have, you may need a suitable audio cable or headphone adaptor.

Key brands at a glance

Focusrite

The 4th Generation Scarlett 2i2 is a two-input option for stereo line sources, with switchable mono and stereo direct monitoring.

  • Focusrite lists two front-panel 6,35 mm line inputs and a stereo mode for Direct Monitoring.
  • Focusrite says that connecting to these inputs disables the corresponding rear XLR microphone inputs. Select stereo monitoring mode for cassette playback.

MOTU

The M2 combines two mic/line/instrument inputs with a headphone socket and metering for input and output levels.

  • MOTU documents direct monitoring in mono or stereo and lists the unit’s dimensions as 19,05 × 10,8 × 4,5 cm.
  • The rear RCA sockets are outputs, not inputs for a cassette deck.

Arturia

The MiniFuse 2 has two inputs, a headphone output and a control for blending the direct signal with computer audio.

  • Arturia describes separate left and right routing for the two inputs when Direct Mono is switched off.
  • Arturia says Direct Mono combines both inputs into a single mono signal. Using direct and software monitoring at the same time can cause an echo.

Behringer

The UMC202HD has two inputs with a line/instrument switch, a headphone output and a direct monitoring switch.

  • Behringer also lists pad switches and signal and clip LEDs.
  • Before buying, check whether direct monitoring on this specific model keeps the two channels separate in stereo.

PreSonus

The Studio 24c has two mic/instrument/line inputs, a headphone output, a monitor mix control and input level indicators.

  • These features are listed in PreSonus product documentation.
  • Before choosing the Studio 24c, check that its direct monitoring plays a stereo source with the left and right channels kept separate.

Matching products at Joybuy

Related products coming soon.

Frequently asked questions

How do I connect a cassette deck with two RCA outputs?

Connect the left and right line outputs to separate line inputs on the interface, then select two channels or stereo in your recording software. Check which cable fits the sockets on your deck and interface. The Audacity Manual notes that a microphone input is not a suitable substitute for the stronger line-level signal.

Why do I hear an echo or both channels in the centre while transferring a tape?

Check whether direct and software monitoring are both active; Arturia lists this combination as a possible cause of echo. Also check the mono/stereo mode on the specific model: Direct Mono on the MiniFuse 2 combines both inputs, while the 4th Generation Scarlett 2i2 has a dedicated stereo direct monitoring mode.

What should I check before transferring a longer tape?

Clean the tape head regularly and make a test recording first. The Audacity Manual recommends checking the loudest section for clipping and gives peaks around −6 dB as a recording guideline.

What extra cables or adaptors might I need?

For stereo, connect the cassette deck’s left and right outputs to separate line inputs. Check the sockets on both devices and make sure your headphones have a suitable connector; depending on the accessories you already have, you may need an audio cable or headphone adaptor.

Can I digitise a music cassette I’ve bought in Germany for my own use?

Under the conditions set out in Section 53(1) of the German Copyright Act (UrhG), individuals may make individual copies for private, non-commercial use. This does not apply to a source that was obviously made or made available to the public unlawfully. It does not amount to general permission to share or publish a copy. Section 95a of the UrhG on effective technological protection measures must also be observed. The legislation is available from the Federal Ministry of Justice and the Federal Office of Justice via the “Laws on the Internet” website.