If your cassette deck or audio interface has a suitable headphone output, wired headphones are an obvious choice because they don’t need charging. If background noise is a problem, consider a closed-back design; open-back or semi-open models may also suit a quiet listening space. Check the plug, adapter and cable length. If you’re using an interface, make sure direct monitoring actually outputs stereo.
Who is this selection for?
People transferring tapes with limited power sockets
You want to listen to the signal through an existing headphone output without needing to charge your headphones as well. Check that the connection is compatible and that your device supports stereo direct monitoring.
People transferring tapes in a busy room
If there’s other noise in the room, you’ll still want to pick up quiet faults in the cassette recording. The headphones’ design and fit both play a part.
People listening for long periods or with care
When you’re listening to a full cassette side, comfort, cable management and the availability of replacement parts all matter. A quiet listening space is also helpful if you want to compare recordings in detail afterwards.
What should you look for when buying?
First, check that the headphone output and monitoring mode work with your tape-transfer setup. Then consider background noise, comfort and the kind of listening comparisons you want to make when choosing a design.
| Your needs |
What to look for |
Who is this most relevant to? |
| Wired connection without charging |
Check the headphone socket, plug type, adapter, cable length and listening volume you can achieve with your actual device. |
If I don’t want to charge another device while transferring tapes, my headphones need to work with the output I already have. This matters most to around 36% of consumers who prioritise connectivity and power requirements. |
| Hearing tape faults despite background noise |
Compare closed-back models and how they fit; test familiar, quiet passages at a moderate volume. |
If you want to listen for quiet faults in a busy room, pay particular attention to the design and fit. This is a priority for around 29% of consumers. |
| Listening to longer cassette sides |
Check how the headphones fit over an extended period, as well as the cable arrangement and replacement parts available for the exact model version. |
If I’m listening for a long time, I want the headband and ear pads to suit me. Comfort and the availability of wear-and-tear parts are the main concern for around 21% of consumers. |
| Comparing recordings in detail |
Listen at comparable volumes and check whether your interface outputs stereo rather than mono in direct monitoring mode. |
If you want to compare the left and right cassette channels separately, consider the monitoring setup alongside the headphone design. This detailed comparison is the top priority for around 14% of consumers. |
Which buying mistakes can you avoid?
-
Assuming direct monitoring is always stereo
On certain older Scarlett versions, both inputs are played in both ears in mono direct monitoring mode. This can give you a misleading impression of the separation between the channels in a recording.
Check your interface’s generation and monitoring mode. Focusrite says the third-generation Scarlett 2i2 has a selectable stereo mode. For stereo comparisons, use the appropriate mode or monitor through your software if necessary.
-
Choosing an open-back model just because it’s on the list
The DT 900 PRO X is open-back, according to the manufacturer. Its appearance in a general list of wired headphones doesn’t mean it will provide enough isolation in a noisy tape-transfer space.
First, consider the noise where you’ll be listening and how much isolation you need. Then compare models with a design suited to that environment.
-
Assuming wired and Bluetooth use are interchangeable
Wireless headphones need a charged battery when used over Bluetooth. Audio-Technica also notes that longer cables for the ATH-M50x aren’t directly compatible with the ATH-M50xBT2.
Check the exact model’s wired mode, socket and required cable length before relying on a wired connection for monitoring.
If the supplied cable is too short for your listening space, you may need a compatible longer cable or an extension.
-
Turning the volume up and up to hear quiet parts of a tape
The German Environment Agency warns that exposure to loud noise can impair hearing or cause permanent damage, depending on its intensity and duration.
Listen at a moderate volume and reduce background noise where possible by choosing a suitable listening space or well-fitting closed-back headphones.
Key brands to consider
beyerdynamic
The DT 770 PRO range comprises closed-back, wired monitoring headphones in several impedance options. The DT 700 PRO X is another closed-back option, while the DT 900 PRO X is open-back.
- beyerdynamic lists replacement parts for the DT 770 PRO, including ear pads and cables. Make sure the impedance option suits your audio source.
- HIFI.DE describes the DT 700 PRO X’s bass as strongly emphasised. This assessment applies to this model, not to every headphone from the brand.
Audio-Technica
The ATH-M40x is a closed-back, wired monitoring headphone; the ATH-M50xBT2 is a wireless option with a few additional connection details to consider.
- Audio-Technica highlights the ATH-M40x’s isolation as a strength. This is the manufacturer’s claim, not an independently measured isolation rating.
- Audio-Technica says that longer cables for the wired ATH-M50x aren’t directly compatible with the ATH-M50xBT2.
RØDE
The NTH-100 is a wired headphone with a detachable cable and an adjustable headband.
- According to RØDE, you can connect the cable to either earcup. This may be useful when arranging the cable in your listening space.
- The comfort and isolation claims come from the manufacturer and don’t replace trying the headphones on. COMPUTER BILD cited the weight as one of the drawbacks of the model it tested.
AKG
The K240 Studio is a wired, semi-open headphone for a quiet listening space.
- AKG specifies a mini-XLR cable connection and a 3-m cable.
- A semi-open design isn’t the best choice if you need maximum isolation in a busy room. Also check that the connection is compatible with your particular audio source.
Sennheiser
The HD 620S is a closed-back, wired headphone for focused listening and comparisons.
- Sennheiser specifies 150 ohms and a 1.8-m cable with a 6.3-mm adapter.
- These specifications don’t tell you how loud the headphones will be with your device. COMPUTER BILD noted warm earcups as one of the drawbacks of the model it tested.
Suitable products at Joybuy
Suitable products will be available soon.
Frequently asked questions
Can I connect the headphones directly to my audio interface instead of using an additional amplifier?
Yes, if your interface has a suitable headphone output. Focusrite explains that direct monitoring routes the input signal to the headphone output. For your specific device generation, also check the stereo mode and whether the output can drive your chosen headphones sufficiently.
Why can’t I hear the two cassette channels separately when using direct monitoring?
This may be due to the mono mode or the generation of your device. Focusrite lists mono direct monitoring on first- to third-generation Scarlett Solo models and first- and second-generation Scarlett 2i2 models. The third-generation Scarlett 2i2 has a selectable stereo mode. Check the manual for your specific interface before judging the recording’s channel separation by what you hear.
What should I maintain or replace after long tape-transfer sessions?
Care for the ear pads and other parts according to the instructions for your particular model, and check for suitable replacements when they wear out. For the DT 770 PRO, beyerdynamic lists ear and head pads as well as cables. This doesn’t mean those parts are interchangeable with other models.
Can I digitise a copy-protected music cassette for personal use?
Under certain conditions, section 53(1) of the German Copyright Act (UrhG) permits individuals to make individual copies for private, non-commercial use. This does not apply to a source that was obviously made or made publicly available unlawfully. Under section 53(6), such copies must not be distributed or played in public. Further restrictions apply to other uses and to circumventing effective technical protection measures.
What are my rights in Germany if a product is faulty or has a manufacturer’s warranty?
When you buy from a trader, EU rules give consumers a statutory guarantee of at least two years for faulty goods. An additional manufacturer’s warranty does not replace these rights; check its terms separately.