Mixing vocals and acoustic instruments
You want to balance vocals and acoustic instruments from a consistent stereo listening position, rather than making a single bass specification your main deciding factor.
Start by choosing a stereo system that you can position symmetrically around your listening spot and connect to your audio source. A compact pair takes up less space; if nearfield monitors are sold individually, you’ll need to plan for two to get stereo. Frequency specifications and room controls are no substitute for sensible positioning or an additional check if you’re unsure about the low end of your mix.
You want to balance vocals and acoustic instruments from a consistent stereo listening position, rather than making a single bass specification your main deciding factor.
You need to fit two speakers alongside your screen and work materials, and want to take into account the possibility of positioning them close to a wall.
You want to assess the lower frequencies of a bass part without treating frequency specifications based on different measurement references as directly comparable.
A good fit if: You have limited desk space and can position two monitors symmetrically. Yamaha lists the HS3 as 132 mm wide per speaker and supplied as a pair.
Trade-off: The stated lower limit of 70 Hz at −10 dB doesn’t, on its own, tell you how reliably you’ll be able to assess the low end of your mix from your listening spot.
A good fit if: You have room for two speakers and want to choose connections and positioning controls that suit your setup.
Trade-off: You’ll need to plan for two units to get stereo with the PreSonus Eris Studio 5 and ADAM Audio T5V; their bass-reflex ports are on different sides.
A good fit if: Saving space is a priority and you can still set up two suitable, symmetrical positions for stereo. Genelec lists the 8010A as 121 mm wide.
Trade-off: Genelec lists 67 Hz at −6 dB. This isn’t measured in the same way as the Yamaha HS3’s −10 dB figure, and it doesn’t demonstrate how well you’ll be able to assess bass in your room.
| What matters | What to look for when buying | Who it matters most to |
|---|---|---|
| Consistent stereo assessment | Check whether both speakers can sit at the same height and symmetrically around your listening spot. Genelec recommends an ideal angle of 60° between the monitors at the listening position. | When I’m balancing vocals and acoustic instruments, I want to be able to compare levels and positioning from a consistent listening spot. Around 36% of consumers would prioritise this kind of repeatable mix assessment. |
| Space and room suitability | Measure the space needed for both speakers, and check the position of the bass-reflex ports and any room controls on the model you’re considering. | When there’s little room on my desk alongside my screen and work materials, I also need to plan for positioning the speakers close to walls. Around 29% of consumers would consider space and room suitability first. |
| Assessing low-pitched instruments | Compare frequency specifications only when you take their respective dB references into account, and plan an additional listening check if you’re unsure about the low end. | When my arrangement includes a clearly audible bass part, I want to check its lower frequencies carefully. Among consumers with this priority, around 21% would put assessing the low end first. |
| Stereo system and connections | Check how many speakers are included, whether connection cables are supplied and whether the inputs match your audio source or audio interface. | I want to make sure I can connect two suitable speakers, rather than accidentally planning for just one. Around 14% of consumers would first look for a complete stereo system and a suitable way to connect it. |
Manufacturers use different dB references: Yamaha lists the HS3 at 70 Hz at −10 dB, ADAM Audio lists the T5V at 45 Hz at −6 dB, and Genelec lists the 8010A at 67 Hz at −6 dB. Your room also affects what you hear from your listening spot.
Take the relevant dB value into account and don’t choose based only on the lowest Hertz figure. Check any uncertain low-end parts of your mix separately.
Yamaha supplies the HS3 as a pair; Genelec lists one 8010A per pack, and PreSonus describes the Eris Studio 5 as an individual speaker.
Before buying, check how many speakers are included, which cables you’ll need and what inputs your audio source has, so you can plan for two monitors you can connect properly.
According to PreSonus, the Eris Studio 5 has a front-facing bass-reflex port and Acoustic Space controls. Genelec also highlights how walls, reflections and listening position can affect what you hear.
First, plan two suitable speaker positions and your listening spot. Then use any available controls to make further adjustments.
The HS3 range is a compact pair for desks with limited space; Yamaha says the HS5 is packaged individually.
The Eris Studio 5 is an individually sold option with a 5.25-inch driver and positioning controls.
The T5V is a 5-inch nearfield monitor sold individually.
The 8010A is an especially compact option, packaged individually, if you can position two speakers effectively.
According to KRK, the ROKIT 5 Generation Five offers settings for mixing and other listening purposes.
Angle both monitors towards your listening spot and aim for the same height and symmetrical distances from the side walls. Genelec recommends an ideal angle of 60° between the speakers at the listening position, but this doesn’t guarantee good room acoustics.
Don’t assume that an active monitor will connect directly: check the audio output on your source and the input on the specific model. Yamaha lists analogue combo, RCA and stereo mini inputs for the HS3, while Genelec lists an analogue XLR input for the 8010A.
For consumer purchases, the seller is generally liable for defects under the statutory warranty; the Verbraucherzentrale states that this lasts two years. For sales contracts made from 31 July 2026, it also explains that the period may be extended once by twelve months if you choose a repair rather than a replacement when a product is faulty. A voluntary manufacturer’s guarantee is separate.
No. The Federal Environment Agency explains that waste electrical equipment must be disposed of separately from household rubbish, and lists local collection points as a way to return it.
No. High volume isn’t a requirement for a better mix. The government health portal gesund.bund.de warns that loud sound can damage your hearing.