Choose a UPS for a small server in a shared studio based on the total load and whether you want the server and network equipment to keep running during a power cut or shut down in an orderly way. The VA rating alone won’t tell you how long it will run. A suitably sized line-interactive UPS can be a good starting point, provided its outlets, runtime at the actual load and shutdown communications suit your setup. If your mains supply is particularly unreliable, consider an online double-conversion UPS. Noise and space are also important in a shared room.
Who is this guide for?
People running an unattended server
If your server runs unattended, you need a suitable power-failure alert and a shutdown function that kicks in at the right time. Schneider Electric describes shutdown options via USB or serial connection, while Synology notes that UPS shutdown support varies by model.
Teams running studio services
If you want your server and essential network equipment to ride out a short power cut together, consider their combined power consumption and the runtime at that exact load. Schneider Electric recommends adding up the power consumption of connected devices; CyberPower and Eaton publish runtime and power specifications for specific models.
Teams in a noise-sensitive space
If the UPS will be close to workstations, consider its footprint and noise levels in each operating mode, as well as its connections. Eaton and BlueWalker/PowerWalker provide model-specific information about noise and fan operation.
What should you look for when buying?
Offline or standby UPS
A good fit if: Basic battery backup for short outages is all you need, and you’ve checked that the switchover behaviour and server power supply are suitable for your specific device.
What to weigh up: A low VA rating alone doesn’t guarantee sufficient runtime or reliable automatic shutdown.
Line-interactive UPS
A good fit if: You want voltage regulation as well as battery backup, and the UPS can keep your devices running at their actual load long enough to continue operating or shut down safely.
What to weigh up: Sine-wave output, communication options, battery-backed sockets and noise levels vary by model.
Online double-conversion UPS
A good fit if: Your mains supply is particularly unreliable, or your specific server application requires a carefully conditioned power supply.
What to weigh up: Before choosing this type, check the specific model’s power consumption, heat output, noise, footprint and runtime.
| Buying priority |
What to check |
Who values it? |
| Orderly shutdown |
Check that the communication method and shutdown software work with your server and operating system; test the process under controlled conditions. |
If my server runs unattended, I need a shutdown process that starts at the right time and works reliably. That’s why around 36% of consumers put safe shutdown first. |
| Runtime for the server and network |
Check the total load in watts against the UPS’s watt and VA limits, then check the runtime at that load. |
If I want my server and essential network equipment to keep running together, I need to consider their combined load. Around 29% of consumers prioritise this backup time. |
| Noise and space |
Check the dimensions and noise or fan specifications for each operating mode. |
If the UPS is close to workstations, I want to know how much space it needs and how it behaves during a power cut or voltage regulation. Around 21% of consumers prioritise how well it fits into a shared space. |
| Outlets and maintenance |
Check the plug type, the number of battery-backed outlets and the model-specific information on replaceable batteries. |
My devices need to be plugged into the right battery-backed sockets for my setup, and I also need to know whether the battery can be replaced later. Around 14% of consumers prioritise suitable connections and maintenance. |
Common selection mistakes
-
Mistaking the VA rating for the runtime
The VA rating doesn’t tell you how long the UPS will provide backup power. CyberPower specifies seven minutes for the CP900EPFCLCD at half its rated load. You can’t apply that figure unchanged to a different load.
Measure the power consumption in watts and check the runtime chart for the exact UPS model at your planned load.
If the backup period is too short, you may not have enough time to shut down safely.
-
Assuming every socket has battery backup
For the Eaton Ellipse PRO ELP850DIN and PowerWalker VI 1000 CSW, the manufacturers distinguish between battery-backed outlets and sockets that only provide surge protection.
Connect your server and essential network equipment to sockets explicitly marked as battery-backed in the specification sheet.
You may need another power solution for a device plugged into an outlet without battery backup.
-
Assuming a USB connection guarantees compatible shutdown
A USB connection alone doesn’t prove that the shutdown process will work with every server. Synology notes that UPS shutdown support varies by brand and model.
Check that your server, UPS model and shutdown software work together, then test the process under controlled conditions.
You may need an additional management connection or a different software configuration, which can take extra time to set up.
-
Only checking noise levels during normal mains operation
According to the manufacturer, the fan on the PowerWalker VI 1000 CSW is off when running on mains power, but runs on battery and in AVR mode.
Think about where you plan to place it and which operating modes it may need to use in the studio.
Key UPS brands to consider
CyberPower
The PFC Sinewave range is worth considering for small server and network loads. The details below refer to the CP900EPFCLCD model.
- CyberPower specifies 900 VA/540 W, pure sine-wave output on battery and six battery-backed Schuko outlets for the CP900EPFCLCD.
- The stated runtime of seven minutes applies at half the rated load. Check the actual runtime and shutdown compatibility for your setup.
Eaton
The Ellipse PRO ELP850DIN is a line-interactive model with Schuko connections that you could consider for a small setup.
- For this model, Eaton specifies 850 VA/510 W, USB-HID, a replaceable battery and three battery-backed Schuko outlets. According to the manufacturer, the fourth Schuko socket only provides surge protection.
- The noise rating of under 25 dB is measured at one metre and doesn’t necessarily apply to every operating mode.
APC by Schneider Electric
The Smart-UPS SMT750IC could be an option for a server with IEC-C13 cabling and a compatible management environment.
- Schneider Electric specifies 750 VA/500 W, pure sine-wave output, six C13 outlets and a shutdown option via serial or USB connection with PowerChute Business Edition for the SMT750IC.
- C13 outlets aren’t Schuko sockets. Check that your cabling, server and software are compatible.
PowerWalker/BlueWalker
The VI 1000 CSW is a line-interactive option with Type F outlets, HID-USB and a replaceable battery.
- BlueWalker/PowerWalker specifies 1000 VA/600 W and pure sine-wave output for this model. Two Type F outlets are battery-backed; the other two only provide surge protection.
- According to the manufacturer, the fan is off when running on mains power and runs on battery and in AVR mode.
Joybuy products
Related products coming soon.
Frequently asked questions
How do I work out what size UPS I need?
Add up the power consumption of the devices you actually want to keep running during a power cut. Check this total load against the watt and VA limits of the specific UPS, then check the runtime at that load. A VA rating alone doesn’t tell you the runtime.
Will a UPS shut down my server automatically?
Not just by being plugged in: you’ll need a suitable communication connection and a shutdown function set up for your server’s operating system. Test the process under controlled conditions. Synology notes that UPS shutdown support varies by brand and model.
What should I consider when placing a UPS in a shared studio?
Compare the dimensions and noise specifications for each operating mode. According to the manufacturer, the fan on the PowerWalker VI 1000 CSW is off when running on mains power, but runs on battery and in AVR mode. This information applies to this model.
What should I know about future maintenance and disposal?
Check whether the specific UPS is designed to take a replaceable battery. In Germany, the Federal Environment Agency recommends taking used batteries to suitable collection points and collecting old electrical equipment separately from household waste. Batteries that can be easily removed should be taken out before old electrical equipment is returned.