Which solution is right for you?

For anyone with a Wi-Fi dead spot between floors

If your workspace is on another floor, first check whether a potential midway location can still receive a usable signal from the router.

For anyone uploading large portfolio files

For larger files, compare the upload speed via LAN at the router with the connection at your workspace. This can help you identify where the bottleneck might be.

For anyone with an existing mesh router

If you want to expand your existing mesh network, check your router model and the features you want against the operating modes explicitly supported by the new device.

What should you look for when buying?

Across multiple floors, the key consideration is how the access point can connect to the router: wirelessly, via Ethernet or over your mains wiring.

Wireless Wi-Fi repeater

Best for: a situation where there’s a spot between the router and your workspace with a usable router signal, and you need to fill a limited Wi-Fi dead spot.

Things to consider: A repeater can only pass on the signal it receives itself; several floors can weaken the wireless backhaul.

LAN bridge or wired access point

Best for: situations where you can run an Ethernet cable to another floor and need Wi-Fi there.

Things to consider: You’ll need a practical route for the cable. Also check the device’s LAN port and supported operating mode.

Multiple mesh nodes

Best for: covering several floors without Ethernet cabling, provided each node gets a usable connection to the previous one.

Things to consider: Multiple nodes can’t bridge a completely unusable wireless connection; advanced mesh features require compatible routers and devices.

Powerline with a Wi-Fi access point

Best for: situations where floors significantly weaken the wireless backhaul, running Ethernet isn’t possible, and you can test the connection at the sockets you plan to use.

Things to consider: devolo recommends powerline for multiple floors, but also notes that transfer rates can be low at individual sockets.

Buying priority What to look for when buying Who is this particularly important to?
A usable connection across floors Check potential midway locations. If the wireless backhaul is weak, consider a LAN bridge or a powerline connection that you’ve tested. If I want to reach my workspace on another floor, I need to know whether a usable router signal reaches the midway location. Around 36% of consumers say coverage between floors is their top buying priority.
Actual upload speed Where possible, measure the upload speed directly via LAN at the router and compare it with the connection at your workspace. Don’t assume advertised Wi-Fi speeds are the same as your internet upload speed. When uploading large portfolio files, I want to find out whether Wi-Fi or my internet connection is limiting the upload. Around 29% of consumers put actual file upload speed first.
Router compatibility Check your router model and mesh system against the repeater’s explicitly supported operating modes. If I want to expand my existing mesh network, I need to know which features are supported by both my router and the new device. Around 21% of consumers say router integration is their top priority.
Installation effort Before buying, check the cable route, how many nodes or adapters you’ll need, and which sockets are available. When choosing between cabling, extra nodes and powerline, I want to know which installation option is practical for my home. Around 14% of consumers prioritise installation effort and total cost.

Common misconceptions

  • Placing the repeater where the router signal is almost gone

    A repeater can only pass on a connection it can still receive. Floors and walls can weaken the signal further.

    Check a midway location where reception is still usable. If there’s no suitable wireless backhaul there, consider a LAN bridge or an alternative you can test on site.

  • Confusing advertised Wi-Fi speeds with your internet upload speed

    A high Wi-Fi speed figure doesn’t prove that your internet connection can upload files faster. Other parts of your home network can also affect the connection.

    Where possible, compare the upload speed directly via LAN at the router with the result at your workspace. The Federal Network Agency’s broadband measurement service uses direct LAN measurements for its evidence procedure.

  • Assuming ‘mesh’ guarantees compatibility with every router

    Extending your Wi-Fi doesn’t automatically mean that all the convenience features of your existing mesh system will be supported.

    Check the full router and repeater models, as well as the mesh mode you want to use. For example, TP-Link says the RE705X requires an EasyMesh-compatible router for its EasyMesh feature.

  • Assuming powerline will be fast on every floor

    Transfer rates can vary from one socket to another; devolo notes that speeds can be low at individual sockets.

    Test the sockets you plan to use and compare the result with the option of running Ethernet.

A guide to the key brands

FRITZ!

The FRITZ!Repeater range includes models for extending a FRITZ! network, as well as devices with LAN ports for a wired connection.

  • According to the manufacturer, the FRITZ!Repeater 6000 and 3000 AX have three wireless units. FRITZ! describes the 1700 as a more compact device with one Gigabit LAN port.
  • According to FRITZ!, the 1700’s stated speed of up to 3.5 GBit/s is a Wi-Fi figure, not a guaranteed internet upload speed.

TP-Link

According to TP-Link, the RE705X combines a dual-band Wi-Fi 6 repeater with Gigabit Ethernet and access point mode.

  • This combination may be useful if you’re considering a LAN bridge as well as wireless coverage extension.
  • According to TP-Link, the RE705X needs an EasyMesh-compatible router to use EasyMesh; advertised Wi-Fi data rates aren’t measured upload speeds.

devolo

devolo offers Wi-Fi repeaters and powerline kits with Wi-Fi access points for connections between floors.

  • The manufacturer recommends powerline for providing Wi-Fi across multiple floors.
  • devolo notes that transfer rates can be low at individual sockets; its recommendation isn’t a guarantee for every building.

Telekom

Speed Home WLAN is a Wi-Fi 6 extension with mesh integration for compatible Speedport routers.

  • Telekom describes a mesh setup with a compatible base unit.
  • If your router doesn’t support mesh, Telekom says Speed Home WLAN can be set up without mesh. Make sure you check your specific router model.

Joybuy products for these connection scenarios

The Joybuy products below include wireless repeaters, a two-unit mesh system and wired access point solutions. Choose based on the connection route available between your router and workspace, and check reception at the location you plan to use.

TP-Link RE190 AC750 wireless repeater, 433 Mbps, white

TP-Link RE190 AC750 Wireless Repeater, 433 Mbps

This wireless repeater is worth considering if there’s still a usable router signal at the midway location. Its signal strength indicator can help you choose where to place it.

AC750; 433 Mbps according to the product name. The Wi-Fi figure isn’t a guarantee of your internet upload speed.

View at Joybuy
MERCUSYS Halo H3000X mesh Wi-Fi system, 2-pack

MERCUSYS Halo H3000X Mesh Wi-Fi System (2-Pack)

This two-unit set is an option if you’re planning to use several Wi-Fi nodes to cover multiple floors. The connection between the nodes needs to be usable at each location.

Wi-Fi 6, AX3000 dual-band; according to the product description, each unit has three Gigabit ports.

View at Joybuy
MERCUSYS ME80X Wi-Fi 6 range extender, AX3000 dual-band, Gigabit port and access point mode

MERCUSYS ME80X Wi-Fi 6 Range Extender (AX3000 Dualband)

It can be used as a wireless repeater where the router signal is usable, or as an access point if you can run an Ethernet cable to the location.

Gigabit port; according to the product description, access point mode requires an Ethernet connection to the router. In repeater mode, the device needs to be in a location that can still receive Wi-Fi from the router.

Advertised Wi-Fi data rates: 574 Mbps at 2.4 GHz and 2402 Mbps at 5 GHz. These figures aren’t a guarantee of your internet upload speed.

View at Joybuy
TP-Link RE235BE BE3600 dual-band Wi-Fi 7 range extender

TP-Link RE235BE BE3600 Dual-Band Wi-Fi 7 Range Extender

As a wireless range extender, it’s suitable for a location that still gets a usable signal from the router.

The product name lists a 2.5 Gigabit Ethernet port, MLO, Smart Roaming and EasyMesh compatibility. Check that your existing router supports the features you want.

View at Joybuy
Ubiquiti UniFi U6+ Wi-Fi 6 access point, dual-band, Gigabit PoE

Ubiquiti UniFi U6+ Wi-Fi 6 Access Point

This wired access point is worth considering if you can run Ethernet to your workspace and want to provide Wi-Fi there.

Dual-band Wi-Fi 6, Gigabit Ethernet port and PoE support (802.3af). An Ethernet connection is required for access point operation.

View at Joybuy

Frequently asked questions

How can I tell whether the repeater or my internet connection is slowing down my portfolio upload?

Where possible, compare the connection at your workspace with an upload speed test directly via LAN at the router. For its official evidence procedure, the Federal Network Agency’s broadband measurement service accepts direct LAN measurements so that Wi-Fi and other network equipment don’t affect the result.

Where should I place a wireless repeater?

Choose a midway location where there’s still a usable connection to the router, rather than placing the repeater at your workspace where reception is very weak. Check the connection indicator there; the same distance won’t work for every floor or home.

Does every repeater automatically become part of my existing mesh network?

No. Check that your router and device work together: according to TP-Link, the RE705X requires an EasyMesh-compatible router for its EasyMesh feature. Telekom describes Speed Home WLAN as supporting both a mesh setup with a compatible base unit and operation without mesh.

What should I check before buying a powerline solution?

Check which adapters are included in the set you’re considering, whether sockets are available where you need them, and whether the connection works well at those locations. devolo notes that transfer rates can be low at individual sockets.