Who is this relevant to?

Students with a Wi-Fi dead spot at their desk

You can access your learning portal near the router, but the connection is unreliable at your study spot, behind internal walls. Deloitte Germany identifies thick walls and poorly positioned routers as possible causes of poor Wi-Fi reception at home.

Homes with Ethernet to the study room

You can run Ethernet to your study room and want to provide Wi-Fi there without sending the signal back through the wall wirelessly. FRITZ! describes connecting a repeater via Ethernet as one way to set up an additional Wi-Fi access point.

Homes without a cable route

You can’t run Ethernet to your study spot, so you’ll need to check whether a wireless node can still get a good connection from an intermediate position, or whether a Powerline connection works from the sockets you plan to use.

What should you look for when buying?

First, compare the connection at the router with the one at your study spot. If the connection works at the router, decide which route back to an additional access point in your home is practical.

The proportions below relate to consumers looking for a solution to access their learning portal through thick internal walls. Each row describes a key buying priority.

Priority What to check before buying Who is it most relevant to?
Reception at your study spot Compare the connection near the router with the one at your desk, and check where the router is positioned. If I need to use the portal at my desk, reception right there is what matters to me. Around 36% of consumers are likely to place the greatest importance on this.
Connection to the access point Check whether Ethernet can run between the two locations. If not, test the wireless connection from an intermediate position or try the adapters in the sockets you plan to use. Anyone planning an additional Wi-Fi access point also needs a reliable connection back to the router. Around 29% of consumers are likely to prioritise this backhaul connection.
Compatibility with your connection and router Check your connection type and whether you need a modem. Also check whether the mesh system works with your existing router in access point or Ethernet backhaul mode. If I add a router or mesh system, I want to make sure the devices suit my existing connection type and configuration. Around 21% of consumers are likely to pay particular attention to this compatibility.
Number of devices and secure use Check how many units you need, what update options are available, and how to set your router password and Wi-Fi encryption. Anyone looking to avoid unnecessary devices and keep their home network secure will consider the size and maintenance needs of the system. Around 14% of consumers are likely to put this first.

Avoiding buying and planning mistakes

  • Buying a faster router without checking the wireless signal path

    Thick walls or a poorly chosen location can affect reception at your study spot, even if your internet connection works at the router.

    Compare the connection at the router with the one at your study spot before deciding whether to move the router, add an access point or replace the router.

    Replacing the router may not remove the need for an additional access point.

  • Putting the mesh node directly in the dead spot

    A node needs a sufficiently good connection to the router itself. If it’s placed behind the wall in the dead spot, its backhaul connection may be weak too. F.A.Z. Kaufkompass highlights the importance of a good connection between mesh units.

    Try an intermediate location. If you can run a cable, consider using an Ethernet backhaul instead.

    Depending on reception, you may need another node or a cable connection added later.

  • Treating a single unit, a multi-pack and a router with a modem as the same thing

    Mesh systems come in different pack sizes. A mesh device without an integrated modem won’t automatically replace the router for your internet connection.

    Before choosing, check how many locations you need to cover, what’s included in the box and what type of internet connection you have.

    Depending on your connection, you may need extra mesh nodes or a separate modem.

  • Checking Powerline compatibility by brand alone

    For the Magic 2 WiFi next, devolo describes compatibility with Magic adapters; according to the manufacturer, dLAN adapters are not supported.

    Check the exact adapter family and test the connection using the sockets you actually plan to use.

    You may need another compatible adapter kit to get the right connection.

Suitable brands to consider

FRITZ!

FRITZ!Box routers and FRITZ!Repeaters are options for different connection types and for extending an existing network.

  • FRITZ! describes the FRITZ!Repeater 2400 as supporting a LAN bridge to the FRITZ!Box.
  • The integrated modem in the FRITZ!Box 7690 is designed for DSL connections. Replacing your router alone doesn’t guarantee sufficient reception at your particular study spot.

TP-Link

Deco systems such as the BE25 and X50 Pro offer mesh units for adding Wi-Fi in other parts of your home.

  • TP-Link lists wired backhaul connections for the BE25 and X50 Pro.
  • Manufacturer claims about wireless speeds or coverage don’t predict how well the connection will work at a particular study spot. For the BE25, also check which pack size you need.

ASUS

AiMesh and ZenWiFi systems are an option if you may want to connect mesh nodes using existing network cabling.

  • ASUS documents Ethernet backhaul and an access point mode for certain AiMesh and ZenWiFi configurations.
  • When connecting via a switch, setup and cabling depend on the operating mode and network configuration.

devolo

Magic Powerline adapters with Wi-Fi can provide an alternative connection to your study area if you can’t run Ethernet and there’s no suitable intermediate location for a wireless node.

  • devolo describes data transmission over power lines, with Wi-Fi provided by the adapter.
  • The Magic 2 WiFi next is compatible with Magic adapters, but not older dLAN adapters, according to the product information. You’ll need to test the connection using the sockets you plan to use.

NETGEAR

Depending on the supported configuration, Orbi mesh systems can connect to a satellite wirelessly or via Ethernet.

  • NETGEAR describes Ethernet backhaul as a connection option and recommends updating the firmware before setup.
  • Whether an Orbi set suits the layout of your home and study spot still depends on positioning the nodes appropriately.

Suitable products on Joybuy

These product options cover mesh Wi-Fi and wired access points, which can provide Wi-Fi in an additional location.

TP-Link Deco BE22 mesh Wi-Fi system, 2-pack

TP-Link Deco BE22, 2-pack

Could be a good fit if you want to set up Wi-Fi in several locations and keep using your existing router in access point mode.

Wi-Fi 7, dual-band and two Gigabit WAN/LAN ports per unit; router and access point modes are listed.

View on Joybuy
TP-Link Deco M4 mesh unit, 1-pack

TP-Link Deco M4, 1-pack

This model may be worth considering as a single extra unit if you want to expand an existing Deco network and use Ethernet backhaul.

AC1200, dual-band and two Gigabit Ethernet ports; the product description lists Ethernet backhaul.

View on Joybuy
TP-Link Deco M4 mesh Wi-Fi system, 3-pack

TP-Link Deco M4, 3-pack

This set may suit a mesh network with several units if you want to keep using your existing router in access point mode.

AC1200, dual-band, Wi-Fi 5 and two Gigabit ports per unit; router and access point modes are listed.

View on Joybuy
TP-Link Deco S4 mesh Wi-Fi system, 3-pack

TP-Link Deco S4, 3-pack

This 3-pack may suit you if you want Wi-Fi in several locations and need to connect wired devices to the units.

AC1200, dual-band, Wi-Fi 5 and two Gigabit ports per unit; the description lists a shared network with roaming.

View on Joybuy
Ubiquiti UniFi U7 Lite Wi-Fi 7 access point

Ubiquiti UniFi U7 Lite

Could be a good choice for a wired access point if you have Ethernet and the necessary network infrastructure in your study area.

Dual-band Wi-Fi 7, 2.5 GbE port and PoE+. Requires an Ethernet connection to a network switch and PoE compliant with 802.3af; the description lists the UniFi Network application for setup.

View on Joybuy

Frequently asked questions

How can I check before buying whether the problem is my internet connection or the Wi-Fi in my study room?

Compare the connection near the router with the one at your study spot. The German Federal Network Agency provides a broadband measurement tool for testing fixed-line internet performance; a poor result only at your study spot doesn’t prove that your internet connection itself is too slow.

Where should I put a wireless mesh node?

Choose a location where the node can still get a sufficiently good connection to the router, then check reception at your study spot. If it’s already behind the wall in a dead spot, its backhaul connection may be weak too. If you have Ethernet, you can test a wired connection instead.

Do I need to replace my internet provider’s router?

Not just because you have a Wi-Fi dead spot. The German Federal Network Agency explains that you’re free to choose a suitable router for your internet connection. Whether replacing it is worthwhile depends on your connection type, existing hardware and the features you need; an additional access point could let you keep using your current router.

What ongoing requirements should I bear in mind?

Work out how many nodes you need and whether you’ll also need cables or Powerline adapters, then check the update options for the specific model. The German Federal Office for Information Security recommends keeping firmware up to date and setting secure router and Wi-Fi passwords. This is security advice, not a guarantee of Wi-Fi performance.

Can I use my own Wi-Fi router in Germany, and what should I look for in a wireless device?

According to the German Federal Network Agency, you’re free to choose a suitable router for your internet connection. Wi-Fi devices placed on the market in Germany must meet the relevant EU conformity requirements, including CE marking and the required accompanying documentation. CE marking doesn’t guarantee that Wi-Fi reception will be strong enough through a particular wall.